Get the most out of your jig grinder
with J-Grinder
3D Measuring
Minimize setup time, maximize quality
We offer a wide range of measuring cycles, both for detecting workpiece zero points and for dimensional inspection.
All measuring cycles are of course checked for collision by 3D simulation.
We will be pleased to program your own measuring cycles for special applications such as e.g. measuring the rotation over two circular surfaces (Fig. 4).
Grinding cycles, measuring and dressing
Reduce the level of knowledge and experience
of your machine operators to a minimum.
Our J-Grinder grinding profile technology requires the operator to roughly define where the workpiece zero point is.Other technologies, such as rotation, zero-point setting, stroke planes, feeds, infeeds, etc., come from the NC program.
We support all manufacturer cycle:
- Closed and open cylindrical / conical contours
- Cylindrical and conical bores / studs
- Radial and vertical tool measurement Single
- Centering cycle
- Cylindrical, conical and profile dressing
Integrated milling cycles
Cut your workpiece machining times in thirds by pre-milling and finish-grinding your contours in one clamping.
We offer profile-integrated milling technology for your jig grinder. Create your milling and subsequent grinding technology with one click.
We offer you the following milling technology:
- 3D contours
- 3D pockets
- Helical milling of blind and through holes
- 3D roughing cycles
- 3D parallel finishing (Fig. 2 & 3)
- Face milling
GCode/DXF to 3D
Modernize your old NC programs.
This module allows you to create 3D models from your old contour programs and 2D DXF drawings and use them for further programming.
Figure 1 shows the 3D model generated from the NC code. The example shows a complete programming of the part with the following functions:
- Measuring the rotation over a planar surface
- XY zero-point calibration via cylindrical surface
- Z zero-point calibration via planar surface
- Finish grinding contours
Figure 2 shows the 3D model generated from the 2D data with features relevant for programming. The example shows a complete programming of the part with the following features:
- Calibrate rotation via planar surface
- XY zero-point calibration via cylindrical surface
- Z zero-point calibration via planar surface
- Contour 2D - Pre-mill contour
- Finish grind contour
We offer you the following options:
- Create 3D models from existing GCode only (Fig. 1)
- Create 3D models from DXF contours and DXF drawings (Fig. 2)
CAM modules
CAM base module
The following features are available in the basic module:
- Contour program for grinding open and closed contours
- Grinding of blind and through holes
- All technology and grinding strategy, such as R-grinding parameters, measuring, dressing, rotation and zero-point, stroke settings, etc. must be done by machine operator
Conical grinding
This module can be used to grind the following features:
- Conical, open or closed contours
- Tapered bores
- Taper pin
Machining profiles
Machining profiles allow you to define strategies for the complete machining of your parts. All manufacturer cycles and all milling cycles are profile-integrated.
Machining profiles allow you to program countless contours or holes with a single click. If desired, the entire technology (allowance, infeed, spark-out, stroke speed and stroke positions, etc.) is defined in the program, so the operator does not have to make any adjustments.
Example Figure 1
- M06 - Select tool, define overflow of upper and lower oscillating positions
- G185 / G285 - Dress tool
- G197 / G297 - Measure tool diameter
- G140 - Grind contour (rough)
- G185 / G285 - Dress tool
- G197 / G297 - Measure tool diameter
- G140 - Grind contour (finish)
3D Measuring
Reduce set-up time by up to two thirds, minimize the qualification of your employees and maximize your accuracy:
- Calibration of the workpiece zero-point
- Calibration of the rotation
- Dimensional control -> 0.001 mm accuracy. With our 3D probe measuring device you do not have to unclamp your grinding tool when checking dimensions. In combination with our calibration device your jig grinder becomes a measuring machine.
- We program you almost all possible special measuring cycles
Post Processor Extension – Multipart
With the Multipart extension you create the maximum production time, whether overnight, over the holidays or over the weekend. The Multipart extension offers you the possibility to produce 24/7. The following variations are possible:
- Up to 8 identical components with different gauge blocks
- Up to 8 different components with identical/different gauge blocks
- Up to 48 identical components with identical gauge blocks
Do you need more than 8? Please contact us.
3D simulation
Avoid scrap parts and damage to your machine by simulating the generated G-code.
- Simulation 3D measuring
- Simulation grinding cycles
- Simulation milling cycles
- The dynamic simulation part (tool with the entire assembly) is checked for collision against ALL static components
Milling cycles – standard
Milling and grinding in one setup is the future. The standard milling cycles include the following features:
- Contour 2D - Milling of open and closed cylindrical contours
- Helix - Milling of blind and through holes.
- Our milling cycles are profile-integrated.
- DirectMIlling - With this feature you can create direct milling operations, even without machining profiles.
Milling Cycles – Extended
With this extension you can turn your jig grinder into a milling machine.
In the figure 1 you can see the clearing of the right contour, the clearing and finishing of the pocket and the clearing and finishing of the rear contour, generated with one click.
Figure 2 shows the finishing toolpaths of the Parallel 3D feature.
The Extended milling cycles contain the following features:
- Clearance cycles
- Parallel 3D
- Contour 3D
- Pockets 3D Face
- Milling
Drilling and countersinking are generally not provided.
If you have a need for these features, please contact us.
Native CAD Import
This module allows you to directly open native 3D files from your CAD system into our CAM system without converting them to the STEP ISO 10303 standard. This saves you a lot of time and especially data storage.
GCode/DXF to 3D CAD-Modul
Create 3D models from your outdated NC programs and DXF sketches or drawings and use them to program timely CAM features.
- Create 3D models from GCode
- In the blink of an eye, create from an old contouring program, a modern and highly efficient program with 3D measuring, milling, machining technologies, etc.
- Create 3D models from DXF sketches and/or drawings